Erica’s Plush Night Light Proposal

My overall concept is a plush night light that needs its own sleeping mask to block out the light!

The Moon: This version would be for a chic, but goofy couple. This bowl is on their wishlist, and this nightlight is on their bed. One partner still wants the lights on at night? No problem, the moon lights up. But hey, the moon and other partner will be wearing eye masks because they’re tryna sleep 😤

The Three-Eyed Monster: Don’t worry little one! Monsters aren’t scary! They can’t scare you because they’re also snoozing!! See its little eye mask? Go on, try taking it on and off. So long as it has that on? You are perfectly safe! And you’re in control! Also, its antennas have a cute glowing light to keep you warm through the night.

The Deep Sea Fish: This one simply appeals to anyone who thinks deep sea fish are awesome. Their dangle-bopper head light is convenient as a reading light on your bedside table. But maybe the fish is ready to go to sleep before you are, so you’ve lended it your eye mask. You’re such good friends supporting each other.

PROTOTYPE

NEXT STEPS

While I hope to make all three, I’ll plan to focus on the three-eyed monster because the moon, well, it doesn’t have an interesting light format to learn with. And the deep sea fish? His head shape doesn’t really lend itself to an eye mask to be honest.

For the three-eyed monster, I’ll hopefully find some funky green fuzzy fabric for the body, embroidered patches for the eyes or felt + buttons, and simpler fabric for the legs, arms, and light up antennas. For the eye mask, I’ll need a silky/satin material and elastic.

Fitbit Teardown

I tore apart the Fitbit Surge with the help of some fit men. Together, we used pliers, an eyeglasses screwdriver, an exacto knife, and our muscles/hands.

note: no fit men were harmed in the tearing down of this fitbit.

Parts and Materials List

  1. Battery cover (metal and foam)
  2. Alkaline button battery
  3. Main Printed Circuit Board including:
    • metal shield,
    • touchscreen controller (Cypress CY8CTMA463),
    • microcontroller (Silicon Labs EFM32 Giant Gecko (ARM Cortex-M3) EFM32GG395F1024),
    • flash memory (Micron Serial NOR Flash N25Q064A11ESEA0F),
    • battery charger (Texas Instruments Battery Charger BQ24232H),
    • GPS receiver (MediaTek GPS Receiver MT3339),
    • Bluetooth controller (Texas Instruments Bluetooth Controller CC2564)
  4. Lithium Polymer battery (LSSP491524AE)
  5. Metal clasps
  6. Rubber liner
  7. Silicone-rubber band
  8. Plastic casing with built-in:
    • charging port
    • pressure sensor (MS5805-02BA01)
  9. Small screws:
    • four 2mm torx screws
    • four 2mm Phillips head screws
    • four 1mm Phillips head screws
  10. Wiring
  11. Glue
  12. Plastic buttons with rubber bumpers
  13. Metal casing
  14. Metal casing with attached wire
  15. Connective wiring and chips
  16. Metal binding with wiring
  17. Foam
  18. Plastic papers
  19. Tape
  20. Sharp thin-film-transistor liquid-crystal display screen (TFT LCD) screen
  21. Silicone-rubber band belt
  22. Metal clasp (nickel and stainless steel)
  23. Silicone-rubber band
  24. Glass display window with wiring
  25. Bluetooth antenna (2 parts)
  26. GPS antenna
  27. Plastic casing with metal screw bearings
  28. Metal casing

Manufacturing the Fitbit

  • Material extraction
  • Injection molding
  • PCB manufacturing (coating, printing, chemical etching, inspecting, soldering, cleaning, plating, laminating etc.)
  • Battery manufacturing (electrode manufacturing, cell assembly, and cell finishing)
  • Assembly

Design elements of interest:

  • The buttons: It was interesting to see how the buttons had little rubber “bumpers” that help the buttons stay in place and are protective buffers against the receptors that they hit when pressure is applied.
  • The band: The band is glued to the Fitbit electronic where the antennas are. It thereby becomes very hard to remove the bands without damaging the antennas. After seeing all the protective measures for the other electronic parts, it becomes very odd to see these pieces unprotected and easily damaged. It has me wondering if the device is built for obsolescence by a company wanting their users to break their products and then buy new ones.